Difference between revisions of "Pe"

From ccitonlinewiki
Jump to: navigation, search
(Design & Optimization of Pressurized Hydrogen Storage)
(Design & Optimization of Pressurized Hydrogen Storage)
Line 16: Line 16:
  
 
1. GFRP (Glass Fiber Reinforced Plastic)
 
1. GFRP (Glass Fiber Reinforced Plastic)
 +
 
2. Alumunium  
 
2. Alumunium  
  
Line 30: Line 31:
  
 
1. Objective and scope analysis
 
1. Objective and scope analysis
 +
 
2. Inventory Analysis
 
2. Inventory Analysis
 +
 
3. Environmental Impact Analysis
 
3. Environmental Impact Analysis
 +
 
4. Result Interpretation
 
4. Result Interpretation

Revision as of 22:38, 1 June 2023

INTRODUCTION Saya Rawhul Ihsan Setyoko dengan NPM 2106639371, mahasiswa Teknik Perkapalan 2021, saya lahir di jakarta 13 Agustus 2003


Resume 26/05/2023

pada hari ini saya belajar untuk bagaimana kita saling mengenal dengan bapak Ahmad Indra, pak DAI berharap bahwa mahasiswa memanfaatkan waktu untuk berinteraksi dengan dosen,belajar mandiri juga penting dan tidak hanya mengandalkan belajar di kelas, pak DAI menjelaskan bagaimana individual study case yang harus dikerjakan, belajar apapun harus melihat realitas, conciesness adalah kondisi dimana kesadaran tidak hanya fisik saja,

pada hari ini saya juga belajar bahwa sebenarnya aspek consciousness merupakan salah satu yang terpenting dalam kehidupan kita, bagaimana kita menggunakan otak kita dalam memproses hal - hal yang terjadi di sekitar kita, dan bagaimana kita menggunakan otak untuk merepresentasikan dunia yang sekarang kita lihat, dimana kesimpulan yang dapat saya ambil adalah bahwa setiap permasalahan pasti membutuhkan aspek conscious untuk menyelesaikannya, bahkan bagaimana kita sebagai manusia mengkonstruksi dunia di sekeliling kita pasti membutuhkan conscious dan kepercayaan bahwa dunia tersebut ada, dapat dilihat pada masalah dimana kita bisa mendapatkan solusinya, namun semua solusi tidak bisa dibuktikan secara exact apakah solusi tersebut benar atau tidak, karena jika bisa dibuktikan maka tidak ada ruang tersisa untuk kepercayaan (faith).

Design & Optimization of Pressurized Hydrogen Storage

the study case is for determine the most efficient design of pressurized hydrogen storage at minimal cost, this are some step recommended by me based on my research

Design Optimization and Material Choosing in some research, the best material for optimazing the performance of the storage is to use layers, layers are the combine system of two or more material to maximise the effect of both material, in this case we use 2 material :

1. GFRP (Glass Fiber Reinforced Plastic)

2. Alumunium

To maximize the performance of the storage, we can use 2 layer of material, those material are 8 mm thickness of alumunium and GFRP(Glass Fiber Reinforced Plastic) Composite with 6 mm thickness, this study is based on numerical method using Finite Element Method to investigate the mechanical behavior of the storage

Using Sorption - Based Storage

The timing between supply and energy demand cause calls for reliable storage system. In this current years, energy storage system become further significant with the widespread implementation of renewable energy. Hydrogen is being a renewable energy with the most demands past the current years, that makes hydrogen storage keep being upgraded to provide the most efficient storage at minimum price, with the research I did from reading many sources, that one journal says that hydrogen storage with sorption based storage system exibit huge potential due to a high energy density. An average temperature lift of 25 °C, energy density of 40 kWh/m3 , and energy efficiency of 73% were obtained.

Do the Life Cycle Assessment method

Life cycle assessment method for determine the tube life cycle from the storage material until it’s not being used anymore, the main factor from this method is knowing whether this storage are toxic to the nature around. the step of doing this assessment are :

1. Objective and scope analysis

2. Inventory Analysis

3. Environmental Impact Analysis

4. Result Interpretation