Difference between revisions of "Ariq Dhifan"

From ccitonlinewiki
Jump to: navigation, search
(Cost Constraints)
(Design and Conclusions)
Line 150: Line 150:
 
[[File:SA_tank.jpg|200px]]
 
[[File:SA_tank.jpg|200px]]
  
From this design that we make using the good material option, analysis said that might be a little bit error of design when we give the tank design pressure at 8 bar there is some area that still red that cause crack or any other risks.
+
From this design that we make using the good material option, analysis said that might be a little bit error of design when we give the tank design pressure at 8 bar there is some area that still red that cause crack or any other risks. Due to its durability, availability, and affordability, using AISI 304 stainless steel as a compressed hydrogen tank material is an excellent choice. However, during tank design and operation, elements like hydrogen embrittlement, a decreased strength-to-weight ratio, and a constrained operational temperature range should be carefully taken into this project.

Revision as of 12:53, 6 June 2023

Introduction

Ariq 081290260277 4x6.jpg

Name: Ariq Dhifan

NPM: 2106657323

Major: Mechanical Engineering KKI

DoB: 22 June 2003

E-mail: ariqdhifan7@gmail.com

Assalamualaikum Hello Everyone! My name is Ariq Dhifan, an undergradute student majoring in Mechanical Engineering at Universitas Indonesia. Currently I am taking Numerical Method class with Pak DAI as my lecturer.

Case Study of Pressurized Hydrogen Storage

The effectiveness, security, and utility of the storage system are all improved as part of the process of optimizing pressurized hydrogen storage. Here are several essential factors for pressurized hydrogen storage optimization:

Tank Design and Materials: The storage tanks' design and materials are crucial to optimization. The tanks may be made out of strong, lightweight materials like high-strength metals or innovative composites while yet preserving structural integrity. Tank shapes that have been optimized can increase storage capacity while still fitting into the available area.

Safety precautions: When dealing with compressed hydrogen, safety is of the highest importance. Leaks may be avoided and the integrity of the storage tanks can be guaranteed by putting strong safety measures into place, such as strict manufacturing standards, quality control processes, and routine inspections. Effective pressure release and venting

Storage Pressure: The energy density and usability of the storage system are influenced by the pressure level at which hydrogen is kept in storage. A greater storage pressure makes it possible to store more hydrogen in a given container, but it also creates issues with tank weight, cost, and safety. Finding the ideal balance between storage pressure, energy density, and pragmatic concerns for the particular application is the goal of optimization.

Systems for Filling and Dispensing: Systems for filling and dispensing are essential for pressurized hydrogen storage. Systems that are optimized should reduce fill time, guarantee precise pressure control during filling, and enable safe and regulated hydrogen dispensing.

Thermal management: Controlling the storage tanks' temperature is crucial for achieving peak performance. Thermal insulation can minimize energy losses and keep the pressure within the appropriate range by reducing heat transfer to the hydrogen that has been stored. As needed, active cooling or heating systems can be used to control the temperature.

System Integration: When optimizing pressurized hydrogen storage, the transportation and end-use systems as well as the storage tanks must all be taken into account. To guarantee effective and flawless operation, integration with fuel cell systems or other hydrogen consumption technologies may be enhanced.

Cost Factors: When doing optimization, it is important to take into account all associated costs, such as those related to materials, production methods, and infrastructure needs. Pressurized hydrogen storage must be widely used, and this depends on finding affordable options that nevertheless retain performance and safety.

Substance That Contained

Hydrogen is a colorless, odorless gas. It is easily ignited. Once ignited it burns with a pale blue, almost invisible flame. The vapors are lighter than air. It is flammable over a wide range of vapor/air concentrations. Hydrogen is not toxic but is a simple asphyxiate by the displacement of oxygen in the air. Under prolonged exposure to fire or intense heat the containers may rupture violently and rocket. Hydrogen is used to make other chemicals and in oxyhydrogen welding and cutting.

Compressed hydrogen (CGH2, CH2 or CGH2) is hydrogen at its gaseous state but kept under pressure, typically at 350 bar (5,000 psi) and 700 bar (10,000 psi). This substance thus simplifies the issue of storing hydrogen, as this element in its gaseous state presents an excessively low density, which meant tank sizes needed to be enormous posing not only logistical but also safety issues. On the other hand, cryo compressed hydrogen is kept at cryogenic (-150º) temperatures, and presents a higher hydrogen density, thus pushing the storage possibilities further. While storing hydrogen has always represented a challenge, the discovery of efficient methods for it is boosting the so-called “hydrogen economy”. In fact, a number of options are being investigated today in search for the right one. At this point, the physical storage of compressed hydrogen in tanks stands out as the technology facilitating onboard automotive storage. Pressure values here remain between 350 and 700 bar (5,000 and 10,000 psi). The main difference would be developing a storage solution that is able not only to generate cryogenic temperatures, but also can be pressurized at nominal pressure levels of between 250-350 atm.

Pressure Tank Material

The density of 304 steel is around 8 g/cm3, or 0.289 lb/in3. Type 304 steel also comes into three main varieties: 304, 304L, and 304H alloys, which chemically differ based on carbon content. 304L has the lowest carbon percentage (0.03%), 304H has the highest (0.04-0.1%), and balanced 304 splits the difference (0.08%). In general, 304L is reserved for large welding components that do not require post-welding annealing, as the low carbon percentages increase ductility. Conversely, 304H is most used in elevated temperatures where the increased carbon content helps preserve its strength while hot.

Type 304 steel is austenitic, which is simply a type of molecular structure made from the iron-chromium-nickel alloy blend. It makes 304 steel essentially non-magnetic, and gives it a lower weakness to corrosion between grains thanks to austenitic steels being generally low carbon. 304 steel welds well using most welding methods, both with and without fillers, and it easily draws, forms, and spins into shape. AISI 304 will be my choice for the tank material due to its cost that relatively cheap and it is also a high-strength material. AISI 304 satisfy our variables in cost realm.


Coding

Initializing Surface Area for hydrogen tank

import numpy as np
from scipy.optimize import minimize

def objective(x):
  # x[0] represents radius, x[1] represents height
  radius = x[0]
  height = x[1]
  
  # Calculate the surface area of ​thte cylinder
  surface_area = 2 * np.pi * radius * (radius + height)
  
  return surface_area

def constraint(x):
  # x[0] represents radius, x[1] represents height
  radius = x[0]
  height = x[1]
  
# Calculate the internal volume of the cylinder
  volume = np.pi * radius**2 * height
    
# Difference between the volume and the desired value
  return volume - 1000

# Initial value of radius and height
x0 = [5.0, 10.0]

# Variable constraints (radius and height)
bounds = [(0, None), (0, None)]

constraint_dict = {'type': 'eq', 'fun': constraint}

result = minimize(objective, x0, method='SLSQP', bounds=bounds, constraints=constraint_dict)

# Optimization results
print("Optimization results:")
print("Radius: {:.2f} cm".format(result.x[0]))
print("Height: {:.2f} cm".format(result.x[1]))
print("Surface Area: {:.2f} cm^2".format(result.fun))

OUTPUT

Optimization results:
Radius: 5.52 cm
Height: 10.43 cm
Surface Area: 553.79 cm^2

Finding The Thickness of The Pressure Tank (8 bar)

r = 5.52e-2 # Tank Radius
p = 800000 # 8 Bar Pressure
t = 2.7e-3 # Minimum Thickness

while t < 11.05e-3:
  hoop = (p * r) / t
  print('Thickness', t, 'hoop stress =', hoop, "Pa")
  t += 1e-3
if hoop > 215e9: #Yield Strength of AISI 304
  break

OUTPUT

Thickness 0.0027 hoop stress = 16355555.555555554 Pa
Thickness 0.0037 hoop stress = 11935135.135135135 Pa
Thickness 0.0047 hoop stress = 9395744.680851063 Pa
Thickness 0.0057 hoop stress = 7747368.421052631 Pa
Thickness 0.0067 hoop stress = 6591044.776119403 Pa
Thickness 0.0077 hoop stress = 5735064.935064935 Pa
Thickness 0.0087 hoop stress = 5075862.068965518 Pa
Thickness 0.0097 hoop stress = 4552577.319587628 Pa
Thickness 0.010700000000000001 hoop stress = 4127102.8037383175 Pa


Cost Constraints

Stainless 304.png

Due to our objective variable that limit our budget at Rp.500.000, We have done research on some distributor website that sell 2-10 mm thick Stainless steel 304 plates. With the thickness 5 mm thick, the material cost at Rp.133.000 with total dimension 5 mm x 20 cm x 20 cm. So, looking from this reference for 553,79 cm^2 surface area it costs around Rp.184.135 for 1 unit. This made us can make another one unit with the same surface area as our backup unit. It satisfy our variable.

Design and Conclusions

Tank design.png Tank design 3.jpg SA tank.jpg

From this design that we make using the good material option, analysis said that might be a little bit error of design when we give the tank design pressure at 8 bar there is some area that still red that cause crack or any other risks. Due to its durability, availability, and affordability, using AISI 304 stainless steel as a compressed hydrogen tank material is an excellent choice. However, during tank design and operation, elements like hydrogen embrittlement, a decreased strength-to-weight ratio, and a constrained operational temperature range should be carefully taken into this project.