File:Model 1.jpg

From ccitonlinewiki
Revision as of 12:58, 3 October 2019 by Andrewdefanto (talk | contribs)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
Model_1.jpg(283 × 178 pixels, file size: 2 KB, MIME type: image/jpeg)

Resume About Design and Analysis of Archimedes Aero-Foil Wind Turbine Blade For Light and Moderate Wind Speed

Wind is an abundant resource and its utilization cannot be affected by climate and weather. Futhermore, it is a resource of the renewable power. The device (wind turbine) are act as the converter from wind kinetic energy into power which can provide electricity for the home, etc. and also large scales. The device itself consist of several parts such as the rotor, generator, control system, and so on. The rotor itself driven by the wind and predefined speeds in term of the wind speed. The orientation of the shaft and rotational axis which are mounted to the turbine define the type of the turbine.


In early ages, shape of the aeroplane wings were used for the model of the turbine blades. Selection of aerofil shape is the most crucial as it is the important variable to deteremine the maximum conversion of the kinetic energy into rotational energy. The journal focused on the Archimedes wind turbine new design. Futhermore, the design are consisting of three circular blade, wrapped around one another which act as coils and then expanded creating a three-dimensional conical turbine. Thus, this design both use the lift and drag force and also guaranteed that wind is drawn into the turbine with an effective angle of 90 degrees by the coils. The image below shows a diagram of Archimedes wind turbine having three blades connected to each other at 120 degrees and symmetric arrangement to the shaft

Model turbin.jpg


The outer diameter of the Archimedes Spiral wind turbine is 1500 mm, the thickness is 5mm and the length is 1500mm.


The design fuction are using the selction of aerofil and the shape aerodynamics are selected for the blade performance. The choice is based on the compairing lift and drag over different aerofils. The dimensions are scaled from the NACA 6409 aerofil shape and scaled to AAWT dimension by using MATLAB. The final design is rather complex.

File:Model turbin ansys.jpg


The analysis of the result is using some methodology such as computational method, mesh generation and boundry setup. From the analysis, we can conclude that using aerofil to and Archimedes wind turbine can increase the torque at a lower speed nearly 15% that AWT, it also shows that the Archimedes wind turbine can extract more power in low and moderate- wind speed than other wind turbine. Futhermore, the design requires less cost which is caused by none of electronic yawning needed because the usage of drag and lift force and also the Archimedes aerofil wind turbine mlooks getting more promising power thand other wind turbine.

File:Model turbin 1.jpg

File history

Click on a date/time to view the file as it appeared at that time.

Date/TimeThumbnailDimensionsUserComment
current12:52, 3 October 2019Thumbnail for version as of 12:52, 3 October 2019283 × 178 (2 KB)Andrewdefanto (talk | contribs)
12:51, 3 October 2019Thumbnail for version as of 12:51, 3 October 2019283 × 178 (2 KB)Andrewdefanto (talk | contribs)
15:25, 2 October 2019Thumbnail for version as of 15:25, 2 October 2019283 × 178 (2 KB)Andrewdefanto (talk | contribs)
15:24, 2 October 2019Thumbnail for version as of 15:24, 2 October 2019284 × 177 (12 KB)Andrewdefanto (talk | contribs)
  • You cannot overwrite this file.

The following file is a duplicate of this file (more details):

The following page links to this file: